anti corrosion resistant coati > absorption tower ceramic lining wearing compound coating

absorption tower ceramic lining wearing compound coating

BD426 desulfurization slurry absorption tower ceramic rubber lining anti wearing
corrosion resistant repair compound epoxy coating

Product description
It’s the high performance wearing abrasion resistant,corrosion resistant polymeric ceramic material compounded by various
high performance wear resistant,corrosion resistant material(like ceramic,silicon carbide,carborundum, titanium alloy) and
modified toughening heat resistant resin.Repairing various pump,valve,pipeline,heat ex-changer end plate,blade of suffering
from room temperature corrosion,also used in the large area corrosion resistant pre-protection,can also be used as the
undercoat and topcoat of corrosion resistant coatings.

Performance features:
BD426 desulfurization slurry circulating pump absorption tower anti corrosion wearing abrasion resistant repair epoxy coating
excellent chemical corrosion resistance
With good performance in erosion resistant,cavitation resistant and impact resistant
High impact strength,with very high bonding strength to the various metal substrates.
Without shrinkage after curing

Product usage:
BD426 desulfurization slurry absorption tower anti chemical corrosion reistant protective coating can excellent acid and alkaline.
Used in the large areas anti corrosion resistant protecting of the equipment.

Product index:

Product name	physical state	Standard packing	Volume (cm³)	Operational time limit (25℃)	Can put into using time (25℃)
BD426 desulfurization slurry absorption tower ceramic rubber lining anti chemical corrosion wearing resistant compound epoxy coating	Semi-fluid	Two component 10kg	7820	45min	24h

Color	Density (g/cm³)	Compressive strength (Mpa) GB1041-2008	Tensile strength (Mpa) GB6329-2008	Shear strength (Mpa) GB7124-2008	Bending strength (Mpa) GB1042-1999	Hardness （Shore D） ASTM-D-2556	Working temperature （℃）
Blue/gray	1.28	90	35	17	43	86	-60～150

How to use:
1.Surface treatment:
Do rust removing and coarsening treatment on the pending-repair part,then clean it by cleaning agent.The substrates after this
treatment should be coarse,clean and dry.

2.The preparation of absorption tower pipeline rubber ceramic lining anti chemical corrosion resistant coating:
According to the mass ratio A:B=5:1 or volume ratio A:B=3.5:1,make A and B two component mix uniformly,then use it up within
specified operation time limit.

3.Coating:
According to criss cross method,make the mixed-up material be coating on the pending-repair part for 2 times,the thickness of
adhesive layer had better be 0.2-0.5mm.The adhesive layer should be compacted,make it fully infiltrates with the substrates.
For large area protection,can brush for 2~3 times according to the actual condition.

4.Curing:
It can be put into using after curing for 24 hours at the temperature of 20-25 degree,if the temperature is low,should heat it up or
prolong curing time to promote the curing.

Packaging specification:
1.Our common packaging:Two-component,10Kg/group,packed in a plastic drum,A component:8.33Kg/drum,
B component:1.67Kg/drum.
2.We could offer you professional customized packaging and sub-package based on users’ requirements.

Transportation storage
Sealed storage in the cool and dry place.The warranty period is 12 months.Avoid placing it upside down,knocking against and
transporting it as a non-dangerous product during transportation.

Special version:
1.This parameter is for laboratory conditions,due to the actual working condition is more complex,suggest the users to do the pretest
according to actual working condition.

2.When the environment temperature is below 15 degree,the curing time will prolong,should take proper heating measure.

3.When the environment temperature is more than 25 degree or the mixing quantity is too large,the curing speed will expedite,
should properly shorten the application time of coating after mixing.

Construction protective measures:
1.Wear the protective masks,wear the protective glasses and rubber gloves
2.Need washing hands with soap before eating,drinking or smoking.
3.The health hazard after touching: a few people will have skin allergy phenomenon,see a doctor in time and avoid touching with
this product again.should wipe it with ethyl acetate when the sizing material paste on the skin by careless,then wash it with clear water.
Should wash it with clear water immediately and see a doctor when splashing into the eyes by careless.

Warm Prompt:
Residual adhesive solution cured products are non-toxic harmless organic solid,but maybe it will produce poisonous gas when
burning,non-professional personnel can not do combustion disposal,should be sent to garbage power plant or garbage burning
place treatment.

fire prevention measures:
Should choose dry powder to extinguish fire,can cover and flap it with dry powder,grit(the construction using abrasive) or
the non chemical fiber fabric when the sizing material catching fire.

Product packaging actual photo of BD426 slurry absorption tower rubber ceramic lining pipeline
anti chemical corrosion chemical repair coating:

------分隔线----------------------------